1. <track id="ibp65"></track>
    <optgroup id="ibp65"></optgroup><optgroup id="ibp65"><i id="ibp65"><code id="ibp65"></code></i></optgroup>
    欧美日韩一区二区综合,欧美粗大无套GAY,国产乱子伦小说,妓女妓女影院妓女影库妓女网
    Shenzhen Grande Electronic Linkedin Page
    Shenzhen Grande Electronic Co., Ltd logo
    E-mail us for a Quote:
    sales88@greattong.com
    Call us now:
    +86-755-83261869

    Technical Article


    How To Make A Good Heat Dissipation Design In PCB Design?

    Time:2021-01-05 14:15:45 Click:

    1. Significance of good heat dissipation

     

    As we all know, MID and VR devices are one of electronic devices. Except for useful work, most of the electrical energy consumed during work is converted into heat and emitted. The heat generated by the electronic equipment causes the internal temperature to rise rapidly. If the heat is not dissipated in time, the equipment will continue to heat up, and the device will fail due to overheating, resulting in a decrease in the reliability of the modified product. At the source end of electronic design, we need to fully consider heat dissipation, which is particularly important for PCB design to plan for making a good heat dissipation design.

     

     

     

     

    2. The factors causing PCB board to heat up

     

    The direct cause of PCB temperature rising that is due to the existence of circuit power consumption devices, which are generally caused by the following factors:

     

    >The device selection is unreasonable and the power consumption is too large;

    > The heat sink is not installed, resulting in abnormal heat conduction;

    > The PCB is locally unreasonable, causing local or global temperature rise;

    > PCB design, routing and heat dissipation design is unreasonable, causing heat concentration.

     

    3. Thermal design PCB design planning

     

    In view of common heat dissipation factors, when we plan the thermal design of PCB design, we propose some common solutions for this factor:

     

    >Components selection

    When selecting a model, the component with low power consumption is preferred under the premise that the same function can be realized. Meanwhile, this is also a cost consideration.

     

    > Components layout

    Before layout, we should start with the heat dissipation module from the Schematic, such as the common PMU module, DCDC module and some unit main control chips with relatively large heat dissipation, as shown in Figure 1. In the layout, we generally place these modules with large heat dissipation in blocks, and separate the non-severe heat dissipation modules with a distance of 3-5mm.

     

     

     

    Figure 1 Distribution of PCB heat dissipation layout

     

    At the same time, if conditions permit, heat sinks can be added to the main control chip with severe heat dissipation, as shown in Figure 2.

     

     

     

     

    Figure 2 Increase the heat sink to enhance the heat dissipation method

     

    3. Treatment of heat dissipation in PCB routing

     

    PCB good copper wiring is also an important way to strengthen heat dissipation:

    1) Add open vias to the heat dissipation pad of the chip, as shown in Figure 3, allowing the heat dissipated by the chip to be introduced into a large area of the same surface to disperse heat through the vias on the heat dissipation pad to achieve the purpose of heat dissipation.

     

     

     

     

    Figure 3 Adding a windowed via on the thermal pad

     

    2) On the basis of perforating the heat dissipation pad, we will increase the heat dissipation area as much as possible. We can add copper leakage on the front and back impedance layers at the same time, and add heat dissipation vias at the same time.

     

     

     

     

    Figure 4 Open windows on the front and back to increase the heat dissipation area

     

    The analysis of the above factors from PCB is an effective way to solve the temperature rise of the printed circuit board. These factors are often related and dependent on each other in a product and system. Most of the factors should be analyzed according to the actual situation, and only for a specific actual situation can solve the problem more correctly and reduce the temperature rise.

     


    Previous:12 Points Need To Know About PCB Design

    Next:The Influence of Software Automation On PCBA Manufacturing


    Request an Official Quote

    Questions

    E-MAIL

    File Upload

    Upload a list of files

      Please upload your Gerber files and BOM. You can upload an unlimited number of files as long as the total size of all files does not exceed 20 MB. To ensure you receive your official quote in less than 24 hours, please include the quantity of circuit boards for which you would like a quote.

      If you require that we sign a Non-Disclosure Agreement (NDA), please send it to us prior to sending your files and we will be happy to accommodate.

       
      Home About Us Services Quality Pb-Free News Contact Us


      Copyright ® 2017,Shenzhen Grande Electronic Co., Ltd. All Rights Reserved. 中文站 Sitemap

      2022年老师你奶真大下面水真多,欧美日韩一区二区综合嗯好舒服嗯好猛嗯好大,国产乱子伦小说免费人成视在线观看不卡,... <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <文本链> <文本链> <文本链> <文本链> <文本链> <文本链>